banner



How To Hang A Wooden Sign

Download Article

Download Article

Stucco is a cement-type siding used in homes around the world. It'due south a potent, tough cloth, which also makes mounting signs or other attachments difficult.[1] While you could hang things on stucco without drilling, they won't be every bit secure equally they would be if you used screws. Luckily, if you have the right tools, the process is much easier. With a masonry drill scrap and masonry screws, you tin hang your sign in no fourth dimension.

  1. ane

    Record a piece of paper to the wall where yous're installing the sign. This is the easiest way to mark your drill holes for the sign. Become to the spot where you want to hang the sign and press a piece of obviously paper at the correct height. Make certain the paper is level, and so tape it down to hold it in identify.[two]

    • If yous have a large sign with multiple brackets, place a piece of paper for each bracket.
  2. ii

    Hang the sign template if it comes with one. Some signs designed for stucco come up with pre-made templates to show you where to drill. Take this template to the spot that you desire to hang the sign and tape it onto the wall simply like a apparently piece of paper.[3]

    • You might besides be able to print a template at dwelling house. Endeavour contacting the company that made the sign to see if they provide a template.
    • Double cheque to make sure that the template is facing right-side upwards. If it's the wrong way, your sign will be upside downwards.
    • Utilize a level and confirm that the template is direct. If either information technology's crooked, your sign might be crooked as well.

    Advertisement

  3. 3

    Press the sign against the newspaper and hold information technology level. If yous're using plain paper as a guide, then you'll need to figure out where to make the screw holes. Hold the sign upward to the paper and printing the brackets against the paper. Suit the sign so it'due south level.[4]

    • If you lot work with a partner, this step will be easier. Ane person tin adjust the sign while the other watches from further back to give directions.
    • A template will already take marks for spiral holes, and then y'all can skip this step if you're using one.
  4. 4

    Poke through the screw holes on the mount to mark the paper. With the sign pressed against the paper, either poke a sharp object through the screw holes or use a marking to make dots in the correct locations. These markings indicate where to drill.[5]

    • If the sign already has studs fastened on the dorsum, so press them into the paper to make minor holes. This shows y'all where to drill.
    • If y'all're using a template, then you tin can skip this step. You lot could also poke minor holes through the markings to brand drilling easier.
  5. Advertisement

  1. one

    Drill holes through the marks on the paper with a masonry drill chip. Attach a masonry drill chip to your power drill, which is designed to penetrate hard materials like stucco. Brand sure the drill chip is smaller than the screws and anchors you're using, about 90% of the size. Ready your drill to a high power and drill into every mark you made on the paper to make pilot holes.[6]

    • If you use anchors, the ballast packaging should indicate what size drill scrap you should use for the pilot holes.
    • Stucco is a tough material, so you may take to press difficult to brand the airplane pilot holes. Be prepared to lean into the drill.
  2. ii

    Remove the paper or template from the wall. Once you make the screw holes in the wall, you don't need the paper equally a guide anymore. Peel off the record and remove all the paper before moving on.[seven]

    • If y'all forget this step, yous could ever peel the newspaper off after you mount the sign.
  3. 3

    Fill each hole with caulk. Employ a caulk gun and insert the tip into the drill hole. Clasp the trigger gently and fill it entirely with caulk. This helps the anchors and screws attach amend. Repeat this for every screw hole y'all made.[8]

    • Caulk comes in clear or white varieties. The appearance is the merely difference. If the holes will be visible after the sign is mounted, so you might want to use a articulate type. If the sign covers the holes, then white is fine.
  4. 4

    Insert an expansion ballast into the holes. Anchors provide actress support for the screws. Accept an ballast and printing information technology into each hole as far every bit y'all can. Then gently tap each anchor with a hammer until it'southward flush with the wall.[nine]

    • Anchors aren't required, only they'll concur the sign much amend than evidently screws. Builders recommend using them whenever you mountain something on stucco.
    • Anchors are available at hardware stores or online. Get a size that matches the screws you're using.
  5. 5

    Line upward the sign'southward mounting bracket with the screw holes. Concord the sign back up to the wall and line upwards its screw holes with the ones in the wall. Press it downward and hold it in place over the holes.[ten]

  6. 6

    Drill masonry screws through the bracket on a low drill setting. Go along the sign pressed against the wall. Drill masonry screws into each hole. Use a depression drill setting for this stride then y'all don't crack the stucco.[11]

    • Don't over-tighten the screws either. This could damage the holes or stucco and loosen the grip on the sign.
    • This part is much easier with 2 people. One can agree the sign while the other drills.
  7. 7

    Push the sign'due south studs into the holes if information technology has them already. Some signs, especially ones designed for stucco, already have studs fastened to them. In this instance, you don't need screws to attach the sign. Just line the studs upwards with the drill holes and printing the sign in as far as it goes. Make sure all the studs are inserted the same amount then the sign is even and apartment.[12]

    • Some signs have spacers already installed on the studs to bear witness how far to push button. If the sign doesn't have spacers, y'all might have to screw them on yourself, so check the packaging to make sure.
  8. 8

    Double-check to ostend that the sign is directly before the caulk dries. One time the caulk dries, it'll be much harder to remove the screws and start over. As soon as you lot mountain the sign, double-check with a level to make sure the sign is directly. Then take a step back and ostend that the sign is where you want it.[13]

  9. Advertisement

Inquire a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertisement

Things Y'all'll Demand

  • Power drill
  • Masonry drill bit
  • Level
  • Hammer
  • Caulk and caulk gun
  • Masonry screws
  • Paper or template
  • Tape
  • Working with a partner volition make this whole job much easier. Ask a friend or family member to spend a few hours with you lot and help.

Thanks for submitting a tip for review!

Advertisement

  • Always use caution when operating ability tools. Wearable gloves and goggles, and keep your fingers away from the moving parts.

Ad

About This Article

Thank you to all authors for creating a folio that has been read 9,901 times.

Did this article help y'all?

Source: https://www.wikihow.com/Hang-a-Sign-on-Stucco

0 Response to "How To Hang A Wooden Sign"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel